Front wheel not centred between the forks
-
- Tricycles are Cool
- Posts: 19
- Joined: Sat Feb 10, 2018 7:48 am
- My Bike: 1987 Intruder 1400
Front wheel not centred between the forks
Hi everyone, last year I had to lay my 87 1400 down. Broken mirror and peg. Everything else seemed ok. I noticed that the fender bolt rubs on the front tire. When I look at the wheel it looks to be .5" to 1" off centre. I had the wheel balanced and the shop said it was good. Why would the wheel be offset. Could the fork be bent and cause this or is it a rim issue?
Any ideas would be helpful.
Any ideas would be helpful.
- hillsy
- Joined a 1200cc Club
- Posts: 8846
- Joined: Wed Sep 17, 2014 12:43 am
Re: Front wheel not centred between the forks
Usually this sort of thing happens when you put the front wheel back on with the spacers on the wrong side.
-
- Joined a 250cc Club
- Posts: 516
- Joined: Wed Mar 02, 2016 4:58 pm
- My Bike: Ummmmmmmm a 1400
- Location: Flyover Country
Re: Front wheel not centred between the forks
You got it right there.hillsy wrote:Usually this sort of thing happens when you put the front wheel back on with the spacers on the wrong side.
- Herb
- Joined a 1200cc Club
- Posts: 19378
- Joined: Sun Oct 26, 2014 9:28 pm
- My Bike: 1999 1400 intruder
Re: Front wheel not centred between the forks
I bought a wrecked bike and fixed it to sell, had the same kind of issue. Turned out that the axel was slightly bent. I couldn't see it but by rotating the axel the alignment of the wheel changed.
Probably a good thing that it happened, I fear the axel might have failed at a really bad time.
Probably a good thing that it happened, I fear the axel might have failed at a really bad time.
I can't seem to win the lottery. I think I have used up all of my good luck riding motorcycles.
- Fred
- WHEELIES R FUN!
- Posts: 4527
- Joined: Tue Dec 02, 2014 12:08 am
- My Bike: VS 1400. Royal Enfield
Re: Front wheel not centred between the forks
You need to do a full fork geometry. firstly the forks should sit up tight in the yoke.
Without the wheel, the spindle should pass right through in perfect allignment.
A dead give away is the brake disk sitting center of the brake caliper.
You can undo and slacken off every thing, thats the spindle and fork clamps, sit on the bike and shake the bars, it will wobble and should settle, re -tighten up all the clamps.
This could be a dangerous bike --get it fixed.
Without the wheel, the spindle should pass right through in perfect allignment.
A dead give away is the brake disk sitting center of the brake caliper.
You can undo and slacken off every thing, thats the spindle and fork clamps, sit on the bike and shake the bars, it will wobble and should settle, re -tighten up all the clamps.
This could be a dangerous bike --get it fixed.
- hillsy
- Joined a 1200cc Club
- Posts: 8846
- Joined: Wed Sep 17, 2014 12:43 am
Re: Front wheel not centred between the forks
He said he had the wheel off the bike to check the balance, so my money is on mixed up spacers when it was put back on.
- Fred
- WHEELIES R FUN!
- Posts: 4527
- Joined: Tue Dec 02, 2014 12:08 am
- My Bike: VS 1400. Royal Enfield
Re: Front wheel not centred between the forks
Cant get it wrong or the brake disc wont fit into the caliper. The caliper is attached to the fork leg.hillsy wrote:He said he had the wheel off the bike to check the balance, so my money is on mixed up spacers when it was put back on.
- hillsy
- Joined a 1200cc Club
- Posts: 8846
- Joined: Wed Sep 17, 2014 12:43 am
Re: Front wheel not centred between the forks
Don't even know if he's got as far as installing the caliper yet. We need more info or pics.Fred wrote:Cant get it wrong or the brake disc wont fit into the caliper. The caliper is attached to the fork leg.hillsy wrote:He said he had the wheel off the bike to check the balance, so my money is on mixed up spacers when it was put back on.
-
- Tricycles are Cool
- Posts: 19
- Joined: Sat Feb 10, 2018 7:48 am
- My Bike: 1987 Intruder 1400
Re: Front wheel not centred between the forks
Sorry for the delay in replying. I'll add a little more information for you guy's. The wheel is currently on the bike. The spacer is on the same side as the rotor. The rubber is about 1/8th of an inch away from the fender mount bolt on the non rotor side and about 1" away on the rotor side. I'm new to this board and not sure how to add a picture. According to the diagram I found the only spacer is on the rotor side.
Thanks to everyone trying to help out its much appreciated.
Thanks to everyone trying to help out its much appreciated.
- hillsy
- Joined a 1200cc Club
- Posts: 8846
- Joined: Wed Sep 17, 2014 12:43 am
Re: Front wheel not centred between the forks
Is the brake caliper on the bike / functioning? If the entire wheel is offset then the caliper shouldn't go on (like Fred said). If it is, then possibly a bent axle (like Herb said).Chad Malette wrote:Sorry for the delay in replying. I'll add a little more information for you guy's. The wheel is currently on the bike. The spacer is on the same side as the rotor. The rubber is about 1/8th of an inch away from the fender mount bolt on the non rotor side and about 1" away on the rotor side. I'm new to this board and not sure how to add a picture. According to the diagram I found the only spacer is on the rotor side.
Thanks to everyone trying to help out its much appreciated.
-
- Tricycles are Cool
- Posts: 19
- Joined: Sat Feb 10, 2018 7:48 am
- My Bike: 1987 Intruder 1400
Re: Front wheel not centred between the forks
Yes calliper is on and functional. Could a bad bearing cause it. Just wondering if it may be a cheaper option.
- hillsy
- Joined a 1200cc Club
- Posts: 8846
- Joined: Wed Sep 17, 2014 12:43 am
Re: Front wheel not centred between the forks
Bad bearing is possible, but you would know about that as soon as you get the weight off the wheel and wiggle it.
Sounds like you need to check the whole front end for straightness. Start with loosening the axle and spinning it in-situ to see any deflection of the wheel.
Sounds like you need to check the whole front end for straightness. Start with loosening the axle and spinning it in-situ to see any deflection of the wheel.
-
- Tricycles are Cool
- Posts: 19
- Joined: Sat Feb 10, 2018 7:48 am
- My Bike: 1987 Intruder 1400
Re: Front wheel not centred between the forks
So this morning I finally had some time to look at the wheel. I removed the fender to see it better. It's definitely 0. 5" more on the non rotor side. When I grab the wheel top and bottom and checked for play in the bearing and there is just enough to say it moves. Should the bearings be replaced or should there be some play? Also can I tighten the spokes on the rotor side to pull the rim over into the center?
Thanks for the help.
Thanks for the help.
- Fred
- WHEELIES R FUN!
- Posts: 4527
- Joined: Tue Dec 02, 2014 12:08 am
- My Bike: VS 1400. Royal Enfield
Re: Front wheel not centred between the forks
Yes there should be a little bit of play and yes you could re true the wheel to pull it over but thats not the problem.Chad Malette wrote:So this morning I finally had some time to look at the wheel. I removed the fender to see it better. It's definitely 0. 5" more on the non rotor side. When I grab the wheel top and bottom and checked for play in the bearing and there is just enough to say it moves. Should the bearings be replaced or should there be some play? Also can I tighten the spokes on the rotor side to pull the rim over into the center?
Thanks for the help.
- WintrSol
- Joined a 450cc Club
- Posts: 857
- Joined: Fri Feb 26, 2016 2:02 pm
- My Bike: CB450 GL1500CT
- Location: Near St. Louis, MO
Re: Front wheel not centred between the forks
Before messing with the spokes, you should first measure the offset of the rim to the hub. A straight edge that just reaches across the wheel to touch the rim on both sides of the hub will be needed, so you can measure the distance from the hub, where the spokes attach, to this straight edge. I can't find a spec on this, but from the structure of the wheel, I believe it should be the same on both sides. If not, you will need a good spoke wrench, and a way to measure the torque with it, so you get all the spokes the same. Also, you will need a way to measure runout of the rim, both side-to-side, as will as concentric. This kind of thing is best left to a wheel shop, unless you are prepared to begin learning to thread spoked wheels.
Florissant, MO
CB450K3, GL1500CTValkyrie
CB450K3, GL1500CTValkyrie
-
- Joined a 1100cc Club
- Posts: 5514
- Joined: Thu Dec 29, 2016 12:33 pm
- My Bike: VS800
Re: Front wheel not centred between the forks
The VS800 wheel and the 1400 wheel are the same.
The hub is NOT centered with the outer rim. The hub is offset and the spokes are longer on one side.
The outer rim should be centered between the forks, but the hub is not.
Have you tried installing the caliper to see where the wheel lays in relation to it?
Be sure the speedometer gear tangs are seated properly in the detents. That could throw the wheel off.
The hub is NOT centered with the outer rim. The hub is offset and the spokes are longer on one side.
The outer rim should be centered between the forks, but the hub is not.
Have you tried installing the caliper to see where the wheel lays in relation to it?
Be sure the speedometer gear tangs are seated properly in the detents. That could throw the wheel off.
- WintrSol
- Joined a 450cc Club
- Posts: 857
- Joined: Fri Feb 26, 2016 2:02 pm
- My Bike: CB450 GL1500CT
- Location: Near St. Louis, MO
Re: Front wheel not centred between the forks
You wouldn't have numbers for this, would you? I don't have access to a wheel right now, so can't measure the offset. I haven't found a spec anywhere, after several searches.navigator wrote:The VS800 wheel and the 1400 wheel are the same.
The hub is NOT centered with the outer rim. The hub is offset and the spokes are longer on one side.
Florissant, MO
CB450K3, GL1500CTValkyrie
CB450K3, GL1500CTValkyrie
-
- Joined a 1100cc Club
- Posts: 5514
- Joined: Thu Dec 29, 2016 12:33 pm
- My Bike: VS800
Re: Front wheel not centred between the forks
The hub assy. is offset to the left sideWintrSol wrote:You wouldn't have numbers for this, would you? I don't have access to a wheel right now, so can't measure the offset. I haven't found a spec anywhere, after several searches.navigator wrote:The VS800 wheel and the 1400 wheel are the same.
The hub is NOT centered with the outer rim. The hub is offset and the spokes are longer on one side.
All measurements are approximate. They were taken with a straight edge and 6" steel scale.
Flange on right spacer faces the wheel. measurements were taken with EBC floating brake disc.
Hub to fork at the spacer, right side = 1.0"
Outside edge of rim to outside of brake disc = 1.2"
Outside edge of rim to outside of 4.5" hub left side = 0.2"
Exposed portion of axle between speedo drive and left fork = 0.7"
Hope this helps.
-
- Tricycles are Cool
- Posts: 19
- Joined: Sat Feb 10, 2018 7:48 am
- My Bike: 1987 Intruder 1400
Re: Front wheel not centred between the forks
The disc slides right into the calipper no problem. Today I tried loosening the fork clamps and axel pulled in the brake and twisted the handle bars To try to realign the forks, that didn't help. I wonder if when I brought the wheel in to be balanced they straightened the run off in the wheel but if it's supposed to be offset they just centred it over the axel.
-
- Joined a 1100cc Club
- Posts: 5514
- Joined: Thu Dec 29, 2016 12:33 pm
- My Bike: VS800
Re: Front wheel not centred between the forks
Compare yours with the measurements I posted above.
usually balancing a wheel does not require any spoke alignment changes.
usually balancing a wheel does not require any spoke alignment changes.