:Parting Out: Engine/Trans shot.. Custom parts up for grabs.
- Herb
- Joined a 1200cc Club
- Posts: 19417
- Joined: Sun Oct 26, 2014 9:28 pm
- My Bike: 1999 1400 intruder
Re: Back wheel locked up.. Engine still runs.. Causes??
Really curious as to what came apart.
A few years ago I had a piece on the shift drum break and it allowed the bike to go into 2 gears at once. Screwed up a bunch of stuff. But when I pulled it down I never saw anything that looked like the parts in the bottom of this tranny.
A few years ago I had a piece on the shift drum break and it allowed the bike to go into 2 gears at once. Screwed up a bunch of stuff. But when I pulled it down I never saw anything that looked like the parts in the bottom of this tranny.
I can't seem to win the lottery. I think I have used up all of my good luck riding motorcycles.
-
- Joined a 1000cc Club
- Posts: 3968
- Joined: Tue Dec 09, 2014 9:58 pm
- My Bike: VS800 Honda Phantom 200
- Fred
- WHEELIES R FUN!
- Posts: 4527
- Joined: Tue Dec 02, 2014 12:08 am
- My Bike: VS 1400. Royal Enfield
Re: Back wheel locked up.. Engine still runs.. Causes??
Some one post up an exploded view of a 800 gearbox. I only got the 1400 stuff. let me have a look at it.
Getting 2 gears at once is a possibility,--if the tumbler is cracked up or the main shaft is floppng about allowing a selector to come out of its slot.
I would like to see the final drive bevel gear out too then we know for sure its inside. I have a feeling the final drive is a taper roller bearing!!!
Getting 2 gears at once is a possibility,--if the tumbler is cracked up or the main shaft is floppng about allowing a selector to come out of its slot.
I would like to see the final drive bevel gear out too then we know for sure its inside. I have a feeling the final drive is a taper roller bearing!!!
-
- Joined a 1000cc Club
- Posts: 3968
- Joined: Tue Dec 09, 2014 9:58 pm
- My Bike: VS800 Honda Phantom 200
Re: Back wheel locked up.. Engine still runs.. Causes??
All I can see that vaguely resemble the 2 pieces lurking are the fork shifter shafts.
[emoji41]
[emoji41]
Grow old disgracefully young man.
- Fred
- WHEELIES R FUN!
- Posts: 4527
- Joined: Tue Dec 02, 2014 12:08 am
- My Bike: VS 1400. Royal Enfield
Re: Back wheel locked up.. Engine still runs.. Causes??
We need a Gynecologist working through little holes like this, you up to the job wash your hands and mask up.
- BRONX INTRUDER
- Joined a 850cc Club
- Posts: 1437
- Joined: Sat Sep 27, 2014 9:00 pm
- My Bike: vs1400
- Location: Clearfield, PA
Re: Back wheel locked up.. Engine still runs.. Causes??
I was thinking i needa get one of them wire cams with display to shove in them holes. Lol.
Lechy; The gear in that pic was removed deliberately to eliminate the starter as the issue. It was replaced and then clutch removed and starter turned engine. Replaced and with any pressure on springs.. It locks engine.
Here's a few more pics...
Little dark as hard to get proper lighting and take pic in there.. But looks like maybe a long bolt bent?
And here's the rollers and debris i used needle nose pliers to retrieve..
Final drive bevel gear... The gears inside the housing to the right of the starter motor that the u-joint connects to?
Will do.. Since i can't fix what i don't know is the exact issue. And i'm curious what happened anyways. Lol.
Lechy; The gear in that pic was removed deliberately to eliminate the starter as the issue. It was replaced and then clutch removed and starter turned engine. Replaced and with any pressure on springs.. It locks engine.
Here's a few more pics...
Little dark as hard to get proper lighting and take pic in there.. But looks like maybe a long bolt bent?
And here's the rollers and debris i used needle nose pliers to retrieve..
Final drive bevel gear... The gears inside the housing to the right of the starter motor that the u-joint connects to?
Will do.. Since i can't fix what i don't know is the exact issue. And i'm curious what happened anyways. Lol.
-
- Joined a 1000cc Club
- Posts: 3968
- Joined: Tue Dec 09, 2014 9:58 pm
- My Bike: VS800 Honda Phantom 200
Re: Back wheel locked up.. Engine still runs.. Causes??
What you are looking at are the shifter drum and shifters inside the casing. If no other damage has been caused it shouldn't be too difficult or costly to replace the shifting forks and shafts, possibly a new drum too. It is major open heart surgery though, engine out and casing split. If you are going to tear into it we would appreciate a blow by blow pictorial.
[emoji41]
[emoji41]
Grow old disgracefully young man.
- Fred
- WHEELIES R FUN!
- Posts: 4527
- Joined: Tue Dec 02, 2014 12:08 am
- My Bike: VS 1400. Royal Enfield
Re: Back wheel locked up.. Engine still runs.. Causes??
The roller type things are a pin meant to locate something prob the tumbler and not too frightening but the aluminium bits are. That is part of the casing and really means thats it.
To continue is engine out, heads off including chains etc. Cylinders off and split the case, about 2 hours.
Its worthless as it is. get stuck in --your pics are great.
Its easy and fun to rip open and engine that you know is not going back together.
To continue is engine out, heads off including chains etc. Cylinders off and split the case, about 2 hours.
Its worthless as it is. get stuck in --your pics are great.
Its easy and fun to rip open and engine that you know is not going back together.
- BRONX INTRUDER
- Joined a 850cc Club
- Posts: 1437
- Joined: Sat Sep 27, 2014 9:00 pm
- My Bike: vs1400
- Location: Clearfield, PA
Re: Back wheel locked up.. Engine still runs.. Causes??
Lechy wrote:What you are looking at are the shifter drum and shifters inside the casing. If no other damage has been caused it shouldn't be too difficult or costly to replace the shifting forks and shafts, possibly a new drum too. It is major open heart surgery though, engine out and casing split. If you are going to tear into it we would appreciate a blow by blow pictorial.
[emoji41]
I wonder what caused the thing to blow. And why bike reads neutral but engine and trans are locked together with pressure of the clutch springs?
If the shifter forks are gone.. And bike reads nuetral.. Shouldn't the engine and trans be disengaged?
I may as well yank the damn thing and get to it; i suppose.
May end up not putting it back together repaired but it's gotta come out regardless. Before i do that though; i think i'll leave the clutch plates out and put the covers and oil back in it to fire the engine up solo. This way i'll get to hear the engine without trans obstruction. Lol.
I'll charge up camera for pics of disection.
-
- Joined a 1000cc Club
- Posts: 3968
- Joined: Tue Dec 09, 2014 9:58 pm
- My Bike: VS800 Honda Phantom 200
Re: Back wheel locked up.. Engine still runs.. Causes??
Could be a part of the shifter fork, the 2 tubes look like parts of the shaft that the shifter forks slide on and are the only hollow tubes in there.
I don't know but it may be possible to access the gear end through the sump plate, it would be interesting to find out.
If the shifter forks are broken the gears could become out of synch thereby causing a lock up, the neutral indicator is activated by a biscuit connection on the end of the shifter drum.
[emoji41]
I don't know but it may be possible to access the gear end through the sump plate, it would be interesting to find out.
If the shifter forks are broken the gears could become out of synch thereby causing a lock up, the neutral indicator is activated by a biscuit connection on the end of the shifter drum.
[emoji41]
Grow old disgracefully young man.
- BRONX INTRUDER
- Joined a 850cc Club
- Posts: 1437
- Joined: Sat Sep 27, 2014 9:00 pm
- My Bike: vs1400
- Location: Clearfield, PA
Re: Back wheel locked up.. Engine still runs.. Causes??
Hmm.. Bicuits forks and plates.. Anyone getting hungry? Lol.Lechy wrote:Could be a part of the shifter fork, the 2 tubes look like parts of the shaft that the shifter forks slide on and are the only hollow tubes in there.
I don't know but it may be possible to access the gear end through the sump plate, it would be interesting to find out.
If the shifter forks are broken the gears could become out of synch thereby causing a lock up, the neutral indicator is activated by a biscuit connection on the end of the shifter drum.
[emoji41]
I'll see if i can get in there at the gear and find anything else before putting covers back on etc.
-
- Joined a 1000cc Club
- Posts: 3968
- Joined: Tue Dec 09, 2014 9:58 pm
- My Bike: VS800 Honda Phantom 200
Re: Back wheel locked up.. Engine still runs.. Causes??
Nah, only way to get in is to split the engine.
Have a look here, items #3 could be the tubes you pulled:
http://www.bikebandit.com/oem-parts/199 ... #sch263227
[emoji41]
Have a look here, items #3 could be the tubes you pulled:
http://www.bikebandit.com/oem-parts/199 ... #sch263227
[emoji41]
Grow old disgracefully young man.
- Fred
- WHEELIES R FUN!
- Posts: 4527
- Joined: Tue Dec 02, 2014 12:08 am
- My Bike: VS 1400. Royal Enfield
Re: Back wheel locked up.. Engine still runs.. Causes??
Why waste money on gaskets and oil its half in bits now. It would take more to refit covers than to drag it out and strip it.
- BRONX INTRUDER
- Joined a 850cc Club
- Posts: 1437
- Joined: Sat Sep 27, 2014 9:00 pm
- My Bike: vs1400
- Location: Clearfield, PA
Re: Back wheel locked up.. Engine still runs.. Causes??
Oh no.. Not putting new gaskets and oil. Lol. Same gaskets and old oil. Lol. Just want to hear the engine alone run. If i'm parting.. I want to make sure certain parts are still good. Lol.Fred wrote:Why waste money on gaskets and oil its half in bits now. It would take more to refit covers than to drag it out and strip it.
- BRONX INTRUDER
- Joined a 850cc Club
- Posts: 1437
- Joined: Sat Sep 27, 2014 9:00 pm
- My Bike: vs1400
- Location: Clearfield, PA
Re: Back wheel locked up.. Engine still runs.. Causes??
Hmm.. That thing i shot a pic of that i thought looked like a bent bolt.. Found other end (head) of it on right side above gear selector..
- BRONX INTRUDER
- Joined a 850cc Club
- Posts: 1437
- Joined: Sat Sep 27, 2014 9:00 pm
- My Bike: vs1400
- Location: Clearfield, PA
Re: Back wheel locked up.. Engine still runs.. Causes??
Engine started and ran but just front cylinder. Felt like rear was dead.. No pulsing air or anything from left port. Oh well.. She's done.
Who wants the red custom expanded tank and fenders with the ghost flames?
Who wants the red custom expanded tank and fenders with the ghost flames?
- BRONX INTRUDER
- Joined a 850cc Club
- Posts: 1437
- Joined: Sat Sep 27, 2014 9:00 pm
- My Bike: vs1400
- Location: Clearfield, PA
Re: Back wheel locked up.. Engine still runs.. Causes??
PS: Lechy; you were right. Those tubes are from the fork shifter. Found that part inside but too big a pc to pull out the hole. Lol.
- BRONX INTRUDER
- Joined a 850cc Club
- Posts: 1437
- Joined: Sat Sep 27, 2014 9:00 pm
- My Bike: vs1400
- Location: Clearfield, PA
Re: Wheel locked up.. Trans shot : Time to Part It Out..
Wondering if i can just cut the neck off and weld it to the 1400 frame since engine is still In it.. Then just build it up. It'll be a vs800 sleeper! Lol.
- BRONX INTRUDER
- Joined a 850cc Club
- Posts: 1437
- Joined: Sat Sep 27, 2014 9:00 pm
- My Bike: vs1400
- Location: Clearfield, PA
Re: Time to Part It Out : Wheel locked up.. Trans shot..
Engine out. Will take pics as i tear down. Lotta crap pc's shaking n moving around inside. Smh.
- BlacktopTravelr
- Joined a 1200cc Club
- Posts: 8992
- Joined: Mon Sep 22, 2014 5:02 pm
- My Bike: Stolen 1-7-15 Returned 1-21-15
- Location: Eufaula, Okla
Re: Time to Part It Out : Wheel locked up.. Trans shot..
Can we slip my 800 motor into that bike? I really like what I see in the pics and the red paint doesn't hurt my opinion of it either. I've only got 130,000 + miles on my bike and need to do something with it. yea, I know it is only just now getting broke in. [space]
(putt putt putt)
90 to 95% of my replies are for my own entertainment