Some may be familiar with this bridge in Durham, NC. Some may have seen some of these videos before. I have seen it many times. I still find it very funny to watch.
11'8"
-
- Back on the Road
- Posts: 3650
- Joined: Sun Jan 10, 2016 6:13 am
- My Bike: Kugelblitz-Kriegshammer 2200
- franktiregod
- Joined a 900cc Club
- Posts: 1818
- Joined: Tue Feb 21, 2017 10:54 am
- My Bike: SUZUKI
Re: 11'8"
They used to have a sign in Griffin, Georgia about 100 feet before a bridge. The sign hung over the road and it said, "If you hit this sign,you will hit that bridge"
I have a picture of it on photobucket somewhere. I thought it was hilarious. Sadly, they have redone the bridge, made it taller, and removed the sign. The really funny part is the bridge still had marks where idiots had hit the sign and the bridge. You cant fix stupid.
I have a picture of it on photobucket somewhere. I thought it was hilarious. Sadly, they have redone the bridge, made it taller, and removed the sign. The really funny part is the bridge still had marks where idiots had hit the sign and the bridge. You cant fix stupid.
- BlacktopTravelr
- Joined a 1200cc Club
- Posts: 8992
- Joined: Mon Sep 22, 2014 5:02 pm
- My Bike: Stolen 1-7-15 Returned 1-21-15
- Location: Eufaula, Okla
Re: 11'8"
When we overlaid the road under a bridge/overpass they always milled the road down whatever depth we were overlaying. Then we had a pole to check to make sure the road was the proper height after it was rolled. If it was short they would send out the milling crew to make it the proper height.
(putt putt putt)
90 to 95% of my replies are for my own entertainment
- Herb
- Joined a 1200cc Club
- Posts: 19268
- Joined: Sun Oct 26, 2014 9:28 pm
- My Bike: 1999 1400 intruder
Re: 11'8"
There used to be a concrete railroad overpass on a highway in northern CA that was at 12' 6". There was this logging company moving a yarder that had a lay down pole that had a 12" I-beam brace on the bottom of the pole (back of lowboy). Total height of the thing was 13'. The truck driver hit the bridge at 80, concrete went everywhere. Took a chunk out of the bridge about 18" wide and 12" high.
I can't seem to win the lottery. I think I have used up all of my good luck riding motorcycles.
- Suzuki Johnny
- Joined a 1200cc Club
- Posts: 33033
- Joined: Wed Dec 10, 2014 5:25 am
- My Bike: 2020 Tri Glide Ultra Harley
- Location: GODS COUNTRY
Re: 11'8"
That is hilarious.....state laws call for a sign with clearance heights on both sides of over passes ..what dumb asses
duc, sequere, aut de via decede
"frapper fort, frapper vite, frappée souvent-- Adm William "Bull" Halsey
“We’re not going to just shoot the sons-of-bitches, we’re going to rip out their living Goddamned guts and use them to grease the treads of our tanks.”--Gen George Patton
"Our Liberty is insured by four "Boxes", the Ballot box, the Jury box, the Soap box and the Cartridge box"
"frapper fort, frapper vite, frappée souvent-- Adm William "Bull" Halsey
“We’re not going to just shoot the sons-of-bitches, we’re going to rip out their living Goddamned guts and use them to grease the treads of our tanks.”--Gen George Patton
"Our Liberty is insured by four "Boxes", the Ballot box, the Jury box, the Soap box and the Cartridge box"
-
- Back on the Road
- Posts: 3650
- Joined: Sun Jan 10, 2016 6:13 am
- My Bike: Kugelblitz-Kriegshammer 2200
Re: 11'8"
At that point they have driven past several large warning signs, and as a last-ditch attempt to get their attention, those flashing yellow warning lights are radar-triggered and come on when a large vehicle is headed towards them...Suzuki Johnny wrote:That is hilarious.....state laws call for a sign with clearance heights on both sides of over passes ..what dumb asses
-
- Back on the Road
- Posts: 3650
- Joined: Sun Jan 10, 2016 6:13 am
- My Bike: Kugelblitz-Kriegshammer 2200
Re: 11'8"
When I drove big trucks I was taught to be especially aware of that situation...low clearances marked less than 14' with new pavement under them. Apparently it has been proven empirically that not all road departments are as careful as you were...BlacktopTravelr wrote:When we overlaid the road under a bridge/overpass they always milled the road down whatever depth we were overlaying. Then we had a pole to check to make sure the road was the proper height after it was rolled. If it was short they would send out the milling crew to make it the proper height.
I was going through NYC one night, and hooked up with a local driver who knew where I needed to go and was headed the same way, and he was brilliantly getting us there on roads and bridges that I would have been nervous about taking...he'd say stuff like "Now this next one says 13' but it's actually about 13' 6", long as they didn't pave it recently...but we'll fit fine now...we just gotta slow down so the trailers don't bounce much..."
I was glad he took point. I could see what was about to happen. He wasn't kidding...we cleared by maybe 3"