Page 1 of 1

Wanting to go tubeless

Posted: Wed Feb 14, 2018 2:28 pm
by Taker73044
Looking for a cheap mag wheel that will fit my bike. I found that some of the m50s had mag wheels and drum brakes and also shaft drive. Does anyone know if these wheels will fit a 2000 vs800 intruder? Direct fit or a bunch of crazy to get it done?

https://m.ebay.com/itm/2005-Suzuki-M50- ... SwB4BaNZNW

Re: Wanting to go tubeless

Posted: Wed Feb 14, 2018 5:00 pm
by hillsy
Taker73044 wrote:Looking for a cheap mag wheel that will fit my bike. I found that some of the m50s had mag wheels and drum brakes and also shaft drive. Does anyone know if these wheels will fit a 2000 vs800 intruder? Direct fit or a bunch of crazy to get it done?

https://m.ebay.com/itm/2005-Suzuki-M50- ... SwB4BaNZNW
I doubt an M50 wheel will be a direct swap. You could "make" it fit, but not sure how complex it would be.

Other option is to seal your spoked rim. There's a million examples on Google and you can even buy kits on eBay.

But the real question is why? I know true tubeless are easier to fix punctures on the road, but you can run a tubeless tyre with a tube.

Re: Wanting to go tubeless

Posted: Wed Feb 14, 2018 5:18 pm
by Taker73044
Wanting to go tubeless mainly for heat reduction and its not fun changing a tube on the side of the road in bfe. A tubeless tire I can just plug, air and go. And sealing spokes is not a great option as spokes tend to turn in time causing the seal to break and they need to be adjusted every so often to keep the wheel true. Mags have no adjustment.

Re: Wanting to go tubeless

Posted: Wed Feb 14, 2018 7:02 pm
by hillsy
Taker73044 wrote:Wanting to go tubeless mainly for heat reduction and its not fun changing a tube on the side of the road in bfe. A tubeless tire I can just plug, air and go. And sealing spokes is not a great option as spokes tend to turn in time causing the seal to break and they need to be adjusted every so often to keep the wheel true. Mags have no adjustment.
Can't say I've ever heard of spokes turning....unless they are not properly tensioned in the first place?

Seriously, sealing spokes is done all the time on dirt bikes. It's not a new thing and it will be your easiest option.

Re: Wanting to go tubeless

Posted: Wed Feb 14, 2018 10:52 pm
by Fred
I dont know what you call heat but they run tubes in Saudi. Most heat is generated from friction especially when accompanied with low pressure. You can buy a heavy duty tubes and believe me its heavy duty alright even difficult to fit. This along with lots of talcum that is a lubricant will give you trouble free riding.

If you must --dont use silcone as every one says, silicone is crap and we can all see it is on the bathroom and kitchen use. There are marine sealants far ahead of silicone that will not come off such as 3M 5200 which is on for good. Or less permenant but still way ahead is sikaflex 291

Re: Wanting to go tubeless

Posted: Wed Feb 14, 2018 11:42 pm
by Forge
Some years of the VS800 came with oem “snowflake” mags. There was a set for sale in the classifieds several months ago. You can also check with Bronx Intruder and see if he has a set.

Re: Wanting to go tubeless

Posted: Thu Feb 15, 2018 1:04 am
by Fred
I know there is one ive seen it, could be off a Honda Shadow. Thing is making it fit is not just spacers it could mean shimming the brake disc to fit in the caliper---IF--- the brake disc is on the right side. Then you got to start swapping forks tubes but that might not be a bad thing as you could have double discs.

Lots of faffing about init. Why no one has done it.

Heavy duty tube and talc.

Re: Wanting to go tubeless

Posted: Thu Feb 15, 2018 11:04 am
by WintrSol
I put about 15K miles on my S50/VS800 on tubeless tires with tubes inside; never had a problem with heat, nor did I ever have a flat. I kept the pressures at that recommended by the tire manufacturer, not the sticker on the bike, which was a lot lower.

I've only ever had two flats since 1968; first one was from a tube that was installed with a pinch, and the second was near a construction site, where I picked up a nail. Maybe I've had exceptional luck, but that's still a lot of miles.

Re: Wanting to go tubeless

Posted: Wed Feb 21, 2018 9:19 am
by BRONX INTRUDER
Forge wrote:Some years of the VS800 came with oem “snowflake” mags. There was a set for sale in the classifieds several months ago. You can also check with Bronx Intruder and see if he has a set.
Thanks brother.
I actually have a front mag.. I can try tracking down a rear.

Re: Wanting to go tubeless

Posted: Mon Mar 19, 2018 1:56 am
by Scotty
In regards to the snowflake wheels. There's someone in KY selling a set.

https://lexington.craigslist.org/mpo/d/ ... 00675.html